What font size fits a name on a place card?
020 3375 6674 info@silverimagelondon.com Open 24 hours, 7 days a week — call or email and we will tell you what is possible today.
For one size across a set of place cards, the widest name on the guest list decides, not the card. On a place card with an 85 mm face and text kept 5 mm inside the cut, the 30-character example name Amelia Wolstenholme-Fitzgerald fits on one line at about 14 pt in Arial, while the 11-character Amelia Hart would fit at 40 pt. Silver Image Print & Signs sets every name from the guest list in one run. The tables below give the largest size that fits for six example names, on three card widths, in four typefaces.
Written by Maciej Antosz, Production Manager at Silver Image London ·
Place cards are designed around one name and printed with a hundred. The sample name in the layout is usually a short one, and the design looks generous until a double-barrelled surname arrives from the list. Checking the longest name first is what stops a set of name cards being reset at the proof.
What is the largest font size that fits each name length?
The largest size is the width of the safe area divided by the width of the name: on an 85 mm face the name has 75 mm, on a 110 mm face 100 mm, and on an A7 card used landscape 95 mm. The figures below were measured by us on 17 November 2026 from the letter widths of four fonts in the versions shipped with macOS 26.3.1, for six invented names set on one line in upper and lower case. They are rounded down to the whole point. The figures are calculated width limits for the example names shown, not recommended reading sizes: names with the same number of characters can be quite different widths, because an m is wider than an i, and the name with the most characters is not always the widest. They leave out the optical kerning a layout program may apply and have not been tested in print, so the final layout is checked at actual size, with its line height, any second line and the fold.
| Name | 85 mm face | 110 mm face | A7 landscape |
|---|---|---|---|
| Zoë Ray (7 characters) | 56 pt | 75 pt | 71 pt |
| Amelia Hart (11 characters) | 40 pt | 54 pt | 51 pt |
| Jonathan Walker (15 characters) | 28 pt | 37 pt | 35 pt |
| Alexandra Thompson (18 characters) | 22 pt | 29 pt | 28 pt |
| Christopher Montgomery (22 characters) | 19 pt | 25 pt | 24 pt |
| Amelia Wolstenholme-Fitzgerald (30 characters) | 14 pt | 19 pt | 18 pt |
The 85 mm face is the business-card size, flat at 85 × 55 mm or as an 85 × 110 mm tent card folding to it; the 110 mm face is the 110 × 120 mm tent card folding to 110 × 60 mm; A7 is 74 × 105 mm. Moving from the 85 mm face to the 110 mm face gives the same name about a third more size.
Does the typeface change the size that fits?
Yes: the same name at the same point size is a different width in each typeface and weight, so the exact font in the artwork is the one to measure. The second table sets three of the example names, Amelia Hart, Alexandra Thompson and Amelia Wolstenholme-Fitzgerald, in four typefaces on the 85 mm face. For these names Times New Roman is the narrowest of the four and Arial Bold the widest, and the difference is one or two points on the longest name and four points on the shortest.
| Typeface | Amelia Hart (11) | Alexandra Thompson (18) | Amelia Wolstenholme-Fitzgerald (30) |
|---|---|---|---|
| Times New Roman | 42 pt | 24 pt | 15 pt |
| Georgia | 38 pt | 22 pt | 14 pt |
| Arial | 40 pt | 22 pt | 14 pt |
| Arial Bold | 38 pt | 20 pt | 13 pt |
Should every card use the same size?
Using one size for every name is a design choice, and where it is made, the widest name decides for all of them. Where that makes the short names look small, there are three ways out. The name can go on two lines, first name above surname, which shortens the longest line. The card can move up to the 110 mm face. Or the longest names can be set a point or two smaller than the rest; any difference in size is compared on a full-size proof.
A second line under the name, such as a company or a table number, is set smaller than the name and has to fit the same safe width. On a job recorded in our mail merge place cards case study, the cards carried the name above the company, with the name bold and larger, on a 110 × 120 mm tent card.
Where does the name go on a tent card?
On a tent card the name goes on the front face, the lower half of the flat sheet; the top half is the back and is upside down once the card stands. The name is repeated on the back only where it should be read from both sides of the table. Text stays 5 mm inside the cut, and the artwork carries 3 mm of bleed. Silver Image Print & Signs supplies one template for each format with the fold line, the cut line and the safe zone marked; sizes, card weights and the templates are on the place card printing page.
The names themselves are sent as a list and not typed into the artwork. How to lay that list out is covered in setting up a spreadsheet of names; the same list drives table plans and ID badges for the same event, and the card for those is in which card for a lanyard name badge.
| Requirement | What we need | Why |
|---|---|---|
| Card size | The face size, and whether the card is flat or a tent | The face width sets the room for the name |
| Safe margin | Names and logos 5 mm inside the cut | Trimming moves by a fraction of a millimetre across a run |
| Guest names | The list as a spreadsheet, one name field in the artwork | Every card is set from the list in one run |
| Widest name | Checked against the safe width before the size is fixed | Where one size is used, the widest name decides it |
Checklist before you fix the name size
- The widest name on the list — tried in the layout in the chosen typeface and weight; the name with the most characters is not always the widest.
- The face width — 85 mm, 110 mm, or the card cut for the job.
- The typeface and weight — a bold or wide face needs a smaller size.
- One line or two — first name above surname where names are long.
- A second line — company or table, set smaller and inside the same width.
- Front only or both sides — on a tent card.
Q&A
What font size should names be on place cards?
The size that lets the widest name on the list fit the safe width of the card. As an indication from our measurements in Arial, on a place card with an 85 mm face the 18-character example Alexandra Thompson fits at about 22 pt and the 30-character Amelia Wolstenholme-Fitzgerald at about 14 pt; on a 110 mm face the same names fit at about 29 pt and 19 pt.
What happens to a name that is too long for the card?
A name too long for one line is set on two lines, set slightly smaller, or the set moves to a wider card. The place to settle it is the proof; on the job in our case study the proof showed every name and not a sample of one.
Is the size of a tent card the folded face or the flat sheet?
Both are given. A tent card from Silver Image Print & Signs is printed flat and folded once: the 85 × 110 mm sheet folds to an 85 × 55 mm face, and the 110 × 120 mm sheet to a 110 × 60 mm face. The name is sized for the face.
Can each card carry a different name from one design?
Yes. Silver Image Print & Signs sets individual names from the guest list in one run, from one design with one name field, on 250, 350, 400 or 450 gsm card.
Quantity, card and finish move the figure. Place cards are quoted on their specification on the place card printing page, printed in London at our London print shop, and what drives print prices generally is in how much printing costs in London. Invitations for the same event are under invitation printing.
Send the design and the guest list
Send the artwork with one name field, the guest list and the card size. The longest names are checked on the proof before the run is printed.
SAP Business Network member registered member