Correx or Foamex: which board for a temporary sign?
020 3375 6674 info@silverimagelondon.com Open 24 hours, 7 days a week — call or email and we will tell you what is possible today.
Correx is the board for a temporary sign outdoors on a fence, a post or a hoarding: fluted polypropylene, waterproof, and rated 6 to 12 months outside. Foamex is the board for indoor and sheltered positions: solid PVC foam, completely flat and better looking close up. Silver Image Print & Signs prints Correx in 3.5, 4 and 5 mm and Foamex in 3 and 5 mm. The short rule on our Correx page is that a sign for a fence is Correx and a sign for a reception is Foamex; the tables below cover the cases in between.
Written by Maciej Antosz, Production Manager at Silver Image London ·
Correx signs and Foamex signs are both rigid, both printed direct to the board, and both cut to size or to a shape, so Correx printing and Foamex printing can look interchangeable on a quote. They are built differently, and the difference shows in three places: how the sign is fixed, how long it stays outside, and how close people stand to it.
What is the difference between Correx and Foamex?
Correx is fluted twinwall polypropylene, two flat printable skins over a corrugated core; Foamex is a solid sheet of PVC foam with a white core. The fluted build is why a full 2440 × 1220 mm sheet of Correx weighs very little, and the polypropylene itself is waterproof all the way through. The solid build is why Foamex is heavier, has a completely flat face and shows its white core on a cut edge.
| Point | Correx | Foamex |
|---|---|---|
| Material | Fluted twinwall polypropylene | Solid PVC foam |
| Thickness | 3.5, 4 or 5 mm | 3 or 5 mm |
| Outdoors | 6 to 12 months | Indoor and short-run outdoor; 1 to 2 years as 5 mm hoarding panels on sheltered runs |
| Close up | Semi-matt face over a fluted core | Completely flat, the better-looking board at reading distance |
| Size range | Single board up to 2440 × 1220 mm, larger as tiled sheets | From A4 up to 240 cm; both dimensions are confirmed at the quote |
| Usual fixing | Eyelets and cable ties, drilled holes for screws, score-folds round a post | On an easel, on a strut back, hung, or on a stand wall |
| Shapes | Contour cut to a vector path | Contour cut when direct-printed |
Which board for which sign?
The position of the sign decides first, and the length of time it stays up decides second. A sign that is cable-tied to mesh fencing or folded round a post is Correx work. A sign that stands on an easel, hangs in a shop or lines an exhibition stand is Foamex work. The table sets out the common cases as starting points from our specifications, not as the only possible choice; the board and the thickness are confirmed against the size, the exposure, the support behind the sign and the way it is fixed.
| The sign | Board | Why |
|---|---|---|
| Site notice on fencing or scaffolding | 4 mm Correx | The default for site work; eyeleted for cable ties |
| Hundreds of short-lived placards or arrows | 3.5 mm Correx | The lightest grade, where unit cost decides |
| Large panel, over 1200 × 900 mm | 5 mm Correx | The thickest grade, which our specification gives for large, unsupported panels; the fixing is checked with the size |
| Hoarding for a build of 6 to 12 months | 4 to 5 mm Correx | Very light and a fraction of the cost |
| Hoarding for 1 to 2 years, sheltered run | 5 mm Foamex | Solid face, lighter than aluminium composite |
| Welcome board on an easel | 5 mm Foamex | The thickness for a board that has to stay flat |
| Exhibition or presentation display | 3 mm Foamex | The display thickness; rigid and light |
| Hanging sign read from both sides | 5 mm Foamex | Printed double-sided |
For longer or more exposed outdoor use than these, the comparison moves on to aluminium composite, which is Dibond printing, set against Foamex in Foamex vs Dibond. Hoarding runs, where all three materials are used, are on the construction hoarding page.
Which board stands up to wind and rain?
Correx is the outdoor board of the two: it is plastic all the way through, so rain does not get into it, and Silver Image Print & Signs rates it at 6 to 12 months outside. Correx bends easily along its flutes and resists bending across them, so on a post or on open mesh fencing our specification runs the flutes vertically and recommends 4 or 5 mm sheet. How a board behaves in wind also depends on its size, its support and its fixings. Mounted flat against a hoarding or a wall, the sheet is supported by the surface behind it.
Foamex is an indoor and short-run outdoor board. Indoors it does not bow, and an A1 board is rigid enough to hold its own weight with one hand. Signs for sites and venues are covered under safety signs and wayfinding signs.
How is each board fixed?
Correx is fixed through the board; Foamex is usually stood, hung or mounted. On Correx, 11 mm eyelets go in the corners, or every 500 mm on a larger perimeter, ready for cable ties. For screw fixing to timber or brick the board is drilled with 4 mm corner holes, and penny washers are recommended to stop the screw head pulling through the flutes. Score-folded channels let a board wrap a square post or stand as a triangle. Artwork stays 10 mm inside the trim and clear of the eyelet and drill positions.
A Foamex board for a reception or an event stands on a folding easel or carries a strut back for a counter, and 5 mm boards printed on both sides are used as hanging signs. Text and logos stay 5 mm inside the cut. Sizes, templates and the two ways a Foamex board is made are on the foam board printing page, and fixing options for Correx on the Correx printing page.
How big can each board be?
The largest single Correx board is the 2440 × 1220 mm master sheet, printed edge to edge; Foamex boards run from A4 up to 240 cm. A Correx sign larger than one sheet is made as tiled sheets designed to butt together, which is how long site runs are done. Display sizes for Foamex, from A4 to A0, are compared in A0 and A1 board printing and display board printing, and file set-up for boards of any size in how to prepare artwork for large format.
Correx is polypropylene, recycling category 5, and a clean board can be taken down, wiped and put up again. Where a sign will be reused across several events or sites, that is a point in favour of Correx outdoors.
Checklist before you choose between Correx and Foamex
- Where the sign goes — fence, post, hoarding, wall, easel, counter or stand.
- Indoors or outdoors, and for how many weeks or months.
- How close people stand to it — across a site, or at reading distance.
- How it is fixed — cable ties, screws, an easel, a strut or hung.
- The size — and whether it is larger than one sheet.
- The thickness — 3.5, 4 or 5 mm Correx; 3 or 5 mm Foamex.
Q&A
Is Correx or Foamex better for an outdoor sign?
For a temporary outdoor sign on a fence, a post or a hoarding, Correx is the better board: waterproof, very light and rated by Silver Image Print & Signs at 6 to 12 months outside. Foamex suits sheltered and short-run outdoor positions, and aluminium composite is the board for years outdoors.
Is Correx or Foamex better for an indoor display?
Foamex is the better board indoors. Foamex is solid, completely flat and does not bow indoors, which is why it is used for easel boards, presentation boards and exhibition displays in 3 or 5 mm.
Which thickness of Correx should a site sign be?
4 mm Correx is the default for signs on scaffolding, fencing and posts. 3.5 mm is for large numbers of short-lived placards, and 5 mm for a large panel with nothing behind it.
Can both boards be cut to a shape?
Yes. Correx and direct-printed Foamex are both contour cut to a vector path supplied with the artwork, so arrows and logo shapes can be made in either board.
Size, thickness, quantity and finishing all move the figure. Each board is quoted on its specification on the Correx printing and foam board printing pages, printed in London at our London sign shop, and what drives print prices generally is in how much printing costs in London. A Foamex job is recorded in our A0 Foamex boards case study.
Tell us where the sign goes
Send the size, the quantity, where the sign will be fixed and how long it stays up. We come back with the board, the thickness and a firm figure.
SAP Business Network member registered member