020 3375 6674 Upload artwork Get a quote 24/7 Printing

How wide is the spine of a perfect bound book?

020 3375 6674 info@silverimagelondon.com Open 24 hours, 7 days a week — call or email and we will tell you what is possible today.

The spine of a perfect bound book is half the page count multiplied by the thickness of one sheet of the text paper. On the text stocks Silver Image Print & Signs runs, 100 pages of 150 gsm silk is 50 leaves at about 0.132 mm, which gives a spine of about 6.6 mm. The same sum gives about 13.2 mm at 200 pages and about 29.7 mm at 450 pages, the largest book we perfect bind. The table below works it out for four papers and nine page counts, and the final figure is confirmed by us before the cover is built.

Written by Maciej Antosz, Production Manager at Silver Image London ·

In perfect binding the cover is one sheet wrapped round the block of pages, so the spine is part of the cover artwork and its width has to be known before the cover can be drawn. A perfect bound cover built on a guessed spine can put the title on the fold of the front cover. The sum takes a minute, and in this estimate it depends on two things: how many pages, and which paper.

How do you calculate the spine width?

Spine width is the number of leaves, which is the page count divided by two, multiplied by the thickness of a single sheet. A leaf is one sheet of paper with a page on each side, so a 200-page book has 100 leaves. Our perfect binding specification gives the spine per 100 pages as about 6.9 mm for 120 gsm uncoated, 5.9 mm for 130 gsm silk, 6.6 mm for 150 gsm silk and 7.2 mm for 170 gsm silk. The table takes the published 300-page spine widths, divides them by 300, multiplies by the page count and rounds to one decimal place. Page counts are interior pages, blank pages included; the cover is a separate sheet. These are estimates for the text block, not measurements of a finished book, which is why the figure is checked before the cover is printed.

Calculated spine width of a perfect bound book in millimetres, by page count and text paper. Page counts from the 24-page minimum to the 450-page maximum.
Pages120 gsm un­coated130 gsm silk150 gsm silk170 gsm silk
241.7 mm1.4 mm1.6 mm1.7 mm
483.3 mm2.8 mm3.2 mm3.5 mm
644.4 mm3.8 mm4.2 mm4.6 mm
966.6 mm5.6 mm6.3 mm6.9 mm
1288.8 mm7.5 mm8.4 mm9.3 mm
16011.0 mm9.4 mm10.6 mm11.6 mm
20013.8 mm11.7 mm13.2 mm14.5 mm
30020.7 mm17.6 mm19.8 mm21.7 mm
45031.1 mm26.4 mm29.7 mm32.6 mm

Uncoated paper is bulkier than silk of a similar weight, which is why the 120 gsm uncoated column is thicker than the 130 gsm silk one. Changing the paper after the cover is drawn changes the spine, so the paper is fixed first.

When is the spine wide enough for a title?

On our perfect binding specification, text is printed on the spine when the calculated spine is 4 mm or wider. A spine thinner than that leaves centred text no room to sit straight. On the sums above, 4 mm is reached at about 56 pages on 170 gsm silk, 58 pages on 120 gsm uncoated, 62 pages on 150 gsm silk and 70 pages on 130 gsm silk. A book just under those counts still gets a square spine; it carries colour and not lettering.

How wide is the cover file?

The cover is one flat file: back cover, spine and front cover side by side, with 3 mm of bleed on all edges. Its width is twice the page width plus the spine plus 6 mm, and its height is the page height plus 6 mm. An A4 book of 200 pages on 150 gsm silk has a 13.2 mm spine, so the cover file is 439.2 mm wide and 303 mm tall; the same book at A5 is 315.2 mm wide and 216 mm tall. These are worked examples; the final cover is built to the spine width we confirm.

Two creases frame the spine, and two hinge creases are scored 7 mm outside it so that the cover opens at the crease and not at the glue joint. The interior is a second PDF of single pages in reading order, never spreads. Covers run on 250 to 400 gsm board and are laminated before they are creased.

Cover file width for a perfect bound book: twice the page width, plus the spine, plus 3 mm bleed at each side. Examples on 150 gsm silk.
BookSpineA4 cover fileA5 cover file
48 pages3.2 mm429.2 × 303 mm305.2 × 216 mm
100 pages6.6 mm432.6 × 303 mm308.6 × 216 mm
200 pages13.2 mm439.2 × 303 mm315.2 × 216 mm
300 pages19.8 mm445.8 × 303 mm321.8 × 216 mm

How much of each page does the spine take?

The glue at the spine conceals roughly 5 to 7 mm of every page, so text and page numbers are kept 12 mm from the spine edge on interior pages. A picture that runs across two facing pages loses its middle unless a gutter shift is applied, so double-page images are flagged with the order. All edges, inside and on the cover, carry 3 mm of bleed, because the book is trimmed on three sides after binding.

Silver Image Print & Signs binds with PUR adhesive, so the same sums apply to what is often called PUR binding. Perfect binding takes 24 to 450 pages, and page counts in between need no multiple of four, as a stapled booklet does. Sizes, papers, laminates and the lead time are on the perfect binding page. Below 24 pages the binding is a stapled booklet, covered under booklet printing, and where a document has to open flat it is wire binding.

What the spine calculation needs, from our perfect binding specification.
RequirementWhat we needWhy
Page countThe final count, from 24 to 450 pagesHalf the page count is the number of leaves
Text paperThe stock and its weightThe thickness of one sheet sets the spine
FilesTwo PDFs: one flat cover, one running interiorThe cover is a single sheet wrapped round the block
GutterText and page numbers 12 mm from the spine edgeSide glue conceals 5 to 7 mm of every page
Bleed3 mm on all edges, interior and coverBooks are trimmed on three sides after binding

Checklist before you build a perfect bound cover

  • The final page count — a late change of eight pages moves the spine by about half a millimetre.
  • The text paper — fixed before the cover is drawn.
  • The spine width — leaves multiplied by sheet thickness, then confirmed by us.
  • Spine text — only where the spine is 4 mm or wider.
  • The cover file — back, spine and front as one flat PDF with 3 mm bleed.
  • The interior — single pages in order, content 12 mm off the spine edge.

Q&A

What is the spine width of a 100-page perfect bound book?

On the text stocks Silver Image Print & Signs runs, a 100-page perfect bound book has a spine of about 5.9 mm on 130 gsm silk, 6.6 mm on 150 gsm silk, 6.9 mm on 120 gsm uncoated and 7.2 mm on 170 gsm silk.

Does the cover thickness count towards the spine?

The sum on our perfect binding specification is leaves multiplied by the thickness of the text paper only. The figure to build the cover to is the one confirmed by us before the cover is built.

How many pages before a title fits on the spine?

Spine text is printed when the calculated spine is 4 mm or wider, which is roughly 60 pages and up depending on the paper: about 56 pages on 170 gsm silk and about 70 pages on 130 gsm silk.

Can the page count be any number?

Perfect binding at Silver Image Print & Signs takes 24 to 450 pages and does not need multiples of four. Confirm the final interior page count, blank pages included, before the spine is calculated.

Page count, size, paper and quantity all move the figure. Perfect bound books are quoted on their specification on the perfect binding page, bound in London at our London print shop; file types are covered in what file format to send for printing, the papers in the paper stocks we hold, and what drives print prices generally in how much printing costs in London.

View all printing services →

Send page count, size and paper

Send the page count, the finished size, the text paper and the cover choice. We confirm the exact spine width and come back with a firm price and a firm date.

SAP Business Network member registered member

Silver Image Print & Signs: a 24-hour print shop in London for same day printing, large format printing, roller banners, Foamex boards, exhibition graphics and document printing.